China Factory for Transient Surge Absorber - Surge Protection Devices – TP10D – Ruilongyuan

China Factory for Transient Surge Absorber - Surge Protection Devices – TP10D – Ruilongyuan

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

All we do is usually connected with our tenet " Customer to start with, Rely on initial, devoting on the food packaging and environmental protection for P6ke250ca , P6ke24 , P6ke43ca , We have now confident that we can easily offer the premium quality products and solutions at resonable price, good after-sales services into the buyers. And we're going to produce a dazzling future.
China Factory for Transient Surge Absorber - Surge Protection Devices – TP10D – Ruilongyuan Detail:

Outdoor and Commercial

Wash wall lighting

LED Lighting

Parking garage/lot

Roadway lighting

lighting

Traffic lighting

Flood lighting

Digital signage

Tunnel lighting

Security power supply

Street lighting

1.UVT: It is an abbreviation of Ultra low voltage triggering technology. It is a design that absorb the high and low voltage energy of the surge in advance. It can absorb the surge energy more completely, and the residual voltage is low, and the protection effect on the back-end equipment is obvious. This technology is patented by Ruilongyuan.

2.Class I: In this paper, a luminaire that refers to “accessible conductive parts connected to protective earthing conductors in fixed wiring” (from IEC60598 – luminaires – general requirements and test – Chinese version).

3.Class II: In this paper, the term “light-protection protection is not only dependent on basic insulation, but also has additional safety measures, such as double insulation or reinforced insulation, but no protective grounding or protection measures depending on installation conditions” (from IEC60598-4.Luminaires – General Requirements and Tests – Chinese version).

4.Leakage current: In this paper, the current flowing through the SPD does not occur when the power is connected. For example, zinc oxide varistor is a device with leakage characteristics.

5.Freewheeling: Current from the connected power source that flows through the SPD during and after the discharge current passes. For example, gas discharge tubes and thyristors are devices with freewheeling characteristics (cited from IEC61643-11).

6.10kA: refers to the maximum discharge current (Imax) in the 8/20μs surge waveform test.

7.10kV: refers to the nominal discharge voltage (Vn) in the 1.2/50μs surge waveform test.

Specification

Test Standard: EN61643-11/ UL14494th

TP20D

Units

Electrical parameters

Rated operating voltage8

277

VAC

Max. Continuous voltage9

277

VAC

Cross-section area (Flexible)

1.3/16

mm2/AWG

Mounting on

Custom

 

Surge parameter

Norminal discharge current10(8/20μs) (In)

5

kA

Max. discharge current11 (8/20μs) (Imax)

10

 kA

Nominal discharge voltage12(1.2/50μs) (Vn)

10

kV

Maximum discharge voltage13(1.2/50μs) (Vmax)

20

kV

Voltage protection level14 (Up)

 

 

L-N/PE

950

V

N-PE

1600

V

Placement and transportation parameters

Enclosure material

ABS765A(94V0)

 

Operating temperature range

-40~80

Ingress Protection

IP65

 

Size

79.5×38.6×16.5

mm

Weight (One piece)

77(±3)

g

Package size

315×290×272

mm

Package quantity

150

pcs

8.Rated operating voltage: The normal AC mains voltage rating assigned by the manufacturer to the SPD (cited from Ul1449).

9.Max. Continuous voltage: The maximum rms voltage that can be continuously applied to the SPD (cited from IEC61643-11).

10.Nominal discharge current: The current peak selected by the manufacturer. With SPD, the current waveform is 8/20μs, and the SPD remains functional after 15 surges (from UL1449)

11.Maximum discharge current: The peak value of the SPD current flowing through the 8/20 waveform and the manufacturer’s claimed amplitude. Belongs to the T2 test type (quoted from IEC61643-11).

12.Nominal discharge voltage: The discharge open circuit voltage peak with a 1.2/50 μs waveform and flowing through the SPD (this parameter is the RUILON laboratory custom parameter, which is equivalent to the open circuit voltage Uoc defined by the T3 test in IEC61643-11).

13.Maximum discharge voltage: The peak value of the SPD voltage flowing through the 1.2/50 waveform and the manufacturer’s claimed amplitude (this parameter is the RUILON laboratory custom parameter, which is twice the open circuit voltage of the T3 test in IEC61643-11). (2Uoc)).

14.Voltage protection level: The maximum voltage expected to occur between the two ends of the SPD due to the application of a specified gradient of the impulse voltage and the specified amplitude and the inrush current of the waveform (cited from IEC61643-11).

Surge test characteristics of TP20D

Test

Surge

Strikess

Pulse Rating

(8/20μs)

10kA

1

8kA

2

5kA

15

3.75kA

45

2.5kA

200

TTF DATE

10kA

2

5kA

50

Nominal discharge voltage: 20kV, 1.2/50μs;

Maximum discharge current: 20kA, 8/20μs;

Executive standard: IEC/EN:61643-11/UL14494th;

Parallel SPD equipment;

UVT ultra-low voltage technology, more adequate protection;

With lead wire for easy connection;

Ultra-thin shape: 79.5  × 38.6  × 16.5, easy to reset;

IP65 waterproof and dustproof;

Installation of Class I and Class II lamps that meet the rated voltage of 110 to 277 VAC;

Excellent performance after TTF’s rigorous testing.

Certified by CB, UL, TUV and CE.

A variety of wiring methods are combined to meet string and parallel wiring requirements.

about uvt

Since the introduction of the 20kV ultra-thin surge suppressor in 2014, Ruilongyuan Electronics has continuously improved its surge protection technology and proposed the theoretical concept of efficient absorption of surge energy. After many tests, the circuit model was established and the ultra-low voltage triggering scheme (UVT1) was introduced. It was applied to the new totem surge suppressor, which greatly improved the surge protection efficiency and played a good role in the protected equipment. Surge protection effect.

Typical installation diagram

Notes:

1.The connection line of the lightning arrester will be  connected after tining.

2.If there are no wiring terminals, wires should be welded,and the welds need to do isolation treatment.

3.L—-Brown;  N—- Blue; P E—Yellow and Green.

Dimensions

Disclaimer Notice -

Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. RUILON products are not designed for, and may not be used in, all applications.


Product detail pictures:

China Factory for Transient Surge Absorber - Surge Protection Devices – TP10D – Ruilongyuan detail pictures


Related Product Guide:

We are experienced manufacturer. Wining the majority from the crucial certifications of its market for China Factory for Transient Surge Absorber - Surge Protection Devices – TP10D – Ruilongyuan , The product will supply to all over the world, such as: kazakhstan, United Arab emirates, Germany, We have 48 provincial agencies in the country. We also have stable cooperation with several international trading companies. They place order with us and export products to other countries. We expect to cooperate with you to develop a larger market.
  • A good manufacturers, we have cooperated twice, good quality and good service attitude.
    5 Stars By Hazel from Canberra - 2018.11.22 12:28
    This company conforms to the market requirement and joins in the market competition by its high quality product, this is an enterprise that have Chinese spirit.
    5 Stars By Andrea from Uzbekistan - 2017.06.19 13:51
    Write your message here and send it to us